
Direct Answer: Pallet Volume Measurement Formula
To measure total pallet volume, measure from the ground to the absolute highest point of the freight (including the wooden skid) and from extreme outside edges (including carton overhang). For Cubic Feet (CFT), use (Length" × Width" × Height") ÷ 1,728. For Cubic Meters (CBM), use (Length cm × Width cm × Height cm) ÷ 1,000,000. For example, a standard 48″ × 40″ GMA pallet stacked to 60″ high equals exactly 66.67 cubic feet or 1.89 CBM.
Accurate pallet volume measurement is the single most effective safeguard against surprise re-weigh, re-class, and dimensioning surcharges from North American LTL (Less-Than-Truckload) carriers and international ocean freight consolidators. Today, nearly every major cross-dock terminal uses overhead infrared and laser dimensioning scanners that automatically measure your pallet’s exact cubic envelope the moment a forklift sets it on the receiving bay floor.
If your Bill of Lading (BOL) underestimates pallet dimensions by even two inches due to stretched film bulging, top-loading cones, or forgetting the height of the wooden skid itself, automated billing systems instantly recalculate your cargo density and append administrative adjustment fees. You can model box-to-pallet arrangements instantly with our Pallet Packing Calculator or verify container volume using our CBM Calculator.
How to Measure a Pallet: The 4 Non-Negotiable Rules
Warehouse loaders frequently make the mistake of measuring only the wooden pallet base (for instance, reading “48×40” off a standard GMA pallet specification sheet) and measuring just the height of their cardboard boxes. Automated freight dimensioners calculate volume based on the largest three-dimensional bounding box surrounding the unitized load:
- Measure Floor-to-Peak Vertical Height: Never subtract the height of the pallet itself. A standard GMA 48×40 stringer or block pallet stands 5 to 6 inches (12.7 to 15.2 cm) tall. Your height tape measure must touch the concrete floor and extend to the highest point of the stacked cartons.
- Capture All Cartons Bulge & Overhang: If poorly stacked cartons overhang the wooden deck boards by 1.5 inches on both the left and right sides, a 40-inch wide pallet physically becomes 43 inches wide. Freight scanners record extreme outer edges, not the wood footprint underneath.
- Include Top-Loading Cones & Corner Boards: Placing a triangular “Do Not Stack” cardboard cone on top of a 52-inch tall pallet increases your official scanned height to 60+ inches, artificially inflating volume and triggering capacity penalties.
- Round Up to the Next Whole Inch or Centimeter: Standard LTL tariff rules round fractional inches upward (e.g., 48.25 inches rounds up to 49 inches) when assessing freight density.
Pallet Volume Formulas: Cubic Feet (CFT) vs. Cubic Meters (CBM)
Depending on whether you ship domestically within North America (LTL road freight) or internationally via air or ocean cargo, your pallet volume will be billed in either Cubic Feet (ft³) or Cubic Meters (m³):
Imperial: Cubic Feet (CFT)
CFT = (L” × W” × H”) ÷ 1,728
Example (48″ × 40″ × 60″):
(48 × 40 × 60) ÷ 1,728 = 115,200 ÷ 1,728 = 66.67 ft³
Metric: Cubic Meters (CBM)
CBM = (L cm × W cm × H cm) ÷ 1,000,000
Example (122 cm × 102 cm × 152 cm):
1,891,488 ÷ 1,000,000 = 1.89 m³
Need to convert quickly between imperial and metric units? Divide total Cubic Feet by 35.315 to get Cubic Meters, or multiply CBM by 35.315 to obtain Cubic Feet. Once you calculate your total CBM, check our guide on how to convert CBM to KG for air and sea freight to estimate chargeable billing weight.
Standard Pallet Volume Reference Matrix (2026)
Use this reference table to look up instant Cubic Feet and CBM totals for North American GMA pallets, European Euro pallets, and Industrial Drum pallets across common warehouse stacking heights (height includes the wooden base):
| Pallet Standard | Base Footprint | Total Height (incl. Skid) | Volume (Cubic Feet) | Volume (CBM) |
|---|---|---|---|---|
| US GMA Pallet (Half) | 48″ × 40″ | 36″ (0.91 m) | 40.00 ft³ | 1.13 CBM |
| US GMA Pallet (Standard) | 48″ × 40″ | 48″ (1.22 m) | 53.33 ft³ | 1.51 CBM |
| US GMA Pallet (Medium) | 48″ × 40″ | 60″ (1.52 m) | 66.67 ft³ | 1.89 CBM |
| US GMA Pallet (Tall) | 48″ × 40″ | 72″ (1.83 m) | 80.00 ft³ | 2.27 CBM |
| US GMA Pallet (Max Trailer) | 48″ × 40″ | 84″ (2.13 m) | 93.33 ft³ | 2.64 CBM |
| Euro EPAL 1 Pallet | 120 cm × 80 cm | 150 cm (59.1″) | 50.85 ft³ | 1.44 CBM |
| Euro EPAL 1 Pallet (Tall) | 120 cm × 80 cm | 180 cm (70.9″) | 61.02 ft³ | 1.73 CBM |
| 4-Drum Square Pallet | 48″ × 48″ | 42″ (1.07 m) | 56.00 ft³ | 1.59 CBM |
How Pallet Volume Controls LTL Density & Freight Class
In domestic trucking, pallet volume directly controls how expensive your shipment will be per hundredweight (CWT). The National Motor Freight Traffic Association (NMFTA) classifies LTL cargo into 18 distinct tiers ranging from Class 50 (dense, inexpensive to haul) up to Class 500 (extremely bulky, expensive to haul). Density is determined strictly by dividing your pallet’s gross scale weight by its measured cubic feet:
Pallet Density (PCF) = Total Pallet Weight (lbs) ÷ Pallet Volume (Cubic Feet)
Using the warehouse photograph banner above as an example: suppose the stacked 48″ × 40″ pallet stands 54 inches tall (60.00 cubic feet) and weighs 440 lbs on the warehouse floor scale (including the 40 lb GMA wood pallet):
Volume = (48 × 40 × 54) ÷ 1,728 = 60.00 ft³Density = 440 lbs ÷ 60.00 ft³ = 7.33 lbs per cubic foot (PCF)
According to standard NMFC density guidelines, a density between 7 and 8 PCF places the pallet into Freight Class 125. However, if a shipper accidentally writes down 72 inches height instead of 54 inches, volume jumps to 80 cubic feet, dropping density to 5.5 PCF and bumping the shipment into Class 175—increasing the invoice by 30% to 45% unnecessarily. Verify your exact classification with our Freight Class Calculator and NMFC Table.
⚠️ Beware the LTL “Cubic Capacity Rule”
Nearly every national LTL carrier enforces a tariff clause known as the Cubic Capacity & Density Minimum Rule. If your multi-pallet shipment occupies 750 cubic feet or more (roughly 10+ linear feet of trailer) while averaging a density under 6 lbs per cubic foot, carriers void your discounted LTL tariff and re-bill the load as a high-cost linear foot or partial truckload charge.
Special Pallet Measurement Case: 55-Gallon Drums & Cylindrical Freight
Measuring pallet volume becomes tricky when unitizing cylindrical freight such as 55-gallon steel or plastic drums, because cylindrical geometry creates overhang traps that violate standard 48×40 GMA deck spaces:
- Standard Drum Footprint: A single 55-gallon closed-head or open-head drum measures approximately 23 inches in diameter and 34.5 inches tall.
- Safe Limit on 48″ × 40″ GMA Pallets (2 Drums Max): Putting 4 drums in a 2×2 grid requires
46" × 46"of square surface area. On a 40-inch wide GMA pallet, 4 drums overhang the edge by 3 inches on each side, forcing carriers to re-measure the width as 46 inches and assess overhang fees. A standard 48×40 pallet safely fits only 2 drums side-by-side with zero overhang. - True 4-Drum Configuration (Use 48″ × 48″ Square Pallets): To load 4 drums safely (~2,000 to 2,200 lbs filled weight), switch to a 48″ × 48″ square drum pallet or 52″ × 52″ spill-containment pallet. At 42 inches total height, a 4-drum unitized pallet occupies 56.00 cubic feet (1.59 CBM).
📦 Related Pallet & Freight Logistics Calculators
Use our complete logistics suite to optimize truckloads, pallet configurations, and carrier pricing:
Pallet Packing Calculator →
Calculate Ti/Hi patterns, box layers, and pallet weight allocations.
How Many Boxes Fit on a Pallet →
Master GMA 48×40 carton stacking, vertical tiers, and weight rules.
CBM to KG Freight Conversion →
Convert ocean 1:1000 and air 1:167 volumetric weights to kilograms.
53ft Truck Pallet Capacity →
Compare 26 straight vs 30 turned pallets and 45,000 lbs axle limits.
2026 Freight, Logistics & Shipping Calculation Hub
Standardized dimensional math, freight class density formulas, and cargo container capacity tools:
Frequently Asked Questions (FAQ)
What is the cubic feet of a standard 48×40 pallet?
A standard 48″ × 40″ GMA pallet has a deck area of 1,920 square inches (13.33 sq ft). At a common 48-inch total height, its volume is 53.33 cubic feet (1.51 CBM). At 60 inches tall, it measures 66.67 cubic feet (1.89 CBM), and at 72 inches tall it equals 80.00 cubic feet (2.27 CBM).
Do you include the wooden pallet height when measuring volume?
Yes. Carriers measure from the bottom floor contact surface up to the highest point of the stacked cartons. Always include the 5 to 6 inches (13 to 15 cm) of the wooden or plastic pallet skid in your height measurement and add 35 to 45 lbs for the pallet weight.
How do you convert pallet cubic feet to CBM?
Divide your total Cubic Feet by 35.315 to get Cubic Meters (CBM). For instance, a 66.67 ft³ pallet divided by 35.315 equals 1.888 CBM (rounded to 1.89 CBM).
What is the LTL Cubic Capacity Rule?
The Cubic Capacity Rule voids standard LTL freight rates if a multi-pallet shipment occupies more than 750 cubic feet of trailer volume while maintaining a density under 6 lbs per cubic foot. Carriers then re-rate the freight based on linear foot occupancy.
How many 55-gallon drums fit safely on a 48×40 pallet?
Only 2 standard 55-gallon drums (each ~23 inches in diameter) fit on a 48″ × 40″ GMA pallet without overhanging the edges. Placing 4 drums on a 48×40 creates 3 inches of overhang on both sides; for 4 drums, use a 48″ × 48″ square drum pallet.
Do “Do Not Stack” cones increase pallet volume?
Yes. Automated overhead laser dimensioners read the tip of the cardboard cone as the load’s maximum vertical height, adding 8 to 10 inches to billed height and potentially triggering “No-Stack” linear-capacity freight surcharges.

Pingback: How to Calculate How Many Boxes Fit on a Pallet: Ti/Hi Guide (2026)